# GLD80 fader trembling help **URL:** \ **Category:** GLD Troubleshooting\ **Created:** [10 February 2022 02:29 UTC](https://forums.allen-heath.com/t/gld80-fader-trembling-help/11871 "2022-02-10T02:29:06Z")\ **Posts on this page:** 10\ **Page:** 1
**Author:** ![mistergrahamb](https://avatars.discourse-cdn.com/v4/letter/m/a587f6/32.png) [@mistergrahamb](https://forums.allen-heath.com/u/mistergrahamb)\ **Post date:** [10 February 2022 02:29 UTC](https://forums.allen-heath.com/t/gld80-fader-trembling-help/11871/1 "2022-02-10T02:29:06Z")
Hi Everyone- new here so thank you in advance for your help. I have a GLD-80 that has a fader ‘trembling’ issue: every time I swap layers, recall a scene, or do anything requiring fader movement, the faders tremble and take quite a bit of time returning to the correct position. Additionally, I see the gain moving up/down in tiny increments constantly in the channel strip display. This happens across all of the faders/channel strips - or seemingly all. The faders come to rest eventually, but the small gain movement in the channel strip continues - even if I manually move a fader up or down to set a new value. Things I have tried: Updated firmware (now on 1.61) Recalibrated faders Factory reset Anyone have any ideas or seen this before? If all else fails I can attempt to RMA to the American distributor, but it will be tough for us to be without a board for whatever length of time that takes. ---
**Author:** ![summitcn](https://sea2.discourse-cdn.com/flex002/user_avatar/forums.allen-heath.com/summitcn/32/2846_2.png) [@summitcn](https://forums.allen-heath.com/u/summitcn)\ **Post date:** [10 February 2022 12:47 UTC](https://forums.allen-heath.com/t/gld80-fader-trembling-help/11871/2 "2022-02-10T12:47:23Z")
The only time that I’ve seen this is when a an app is connected to the mixer at the same time, and was causing a conflict for some reason. If you have networked remote control in-use try removing it and seeing if it still does it. If that’s not the case, you likely have a faulty fader. ---
**Author:** ![joe-hinkens](https://sea2.discourse-cdn.com/flex002/user_avatar/forums.allen-heath.com/joe-hinkens/32/929_2.png) [@joe-hinkens](https://forums.allen-heath.com/u/joe-hinkens)\ **Post date:** [10 March 2024 23:53 UTC](https://forums.allen-heath.com/t/gld80-fader-trembling-help/11871/3 "2024-03-10T23:53:52Z")
I have this exact same issue as the OP and have conducted the following: Updated Firmware to 1.61 Recalibrated faders Spray electrical contact cleaner in the faders Conducted a hard factory reset Any ideas or recommendations? I should note that this mixer is extremely clean and was used on a limited basis since new, but hasn’t been turned on for a couple of years. Thanks, Joe ---
**Author:** ![joe-hinkens](https://sea2.discourse-cdn.com/flex002/user_avatar/forums.allen-heath.com/joe-hinkens/32/929_2.png) [@joe-hinkens](https://forums.allen-heath.com/u/joe-hinkens)\ **Post date:** [11 March 2024 00:31 UTC](https://forums.allen-heath.com/t/gld80-fader-trembling-help/11871/4 "2024-03-11T00:31:41Z")
I also replaced the 2032 battery which was completely flat and still no joy. Faders continue to jitter or chatter and the channel strip values continue to fluctuate erratically by 0.1db or 0.2db. ---
**Author:** ![unicomix](https://avatars.discourse-cdn.com/v4/letter/u/e19b73/32.png) [@unicomix](https://forums.allen-heath.com/u/unicomix)\ **Post date:** [20 April 2024 04:56 UTC](https://forums.allen-heath.com/t/gld80-fader-trembling-help/11871/5 "2024-04-20T04:56:31Z")
The same symptoms are occurring on one of my GLD80s. All the faders are moving up and down slightly. It vibrates especially violently when the fader is ganged or when the DCA gain is fixed at 0db. I tried cleaning the internal USB wiring contacts, but it didn’t improve. There was a post with similar symptoms in the GLD user group on Facebook. Among the replies, someone said that replacing the capacitor would fix the problem. Content You can repair the fader board. Replace capacitor, value 1mf/50v and 10mf/16v. Replace all capacitor (SMD) on the fader board. > **[15 comments | Hey guys, new here trying to determine what is going on here...](https://www.facebook.com/reel/267231886317164)** > > Hey guys, new here trying to determine what is going on here and hoping I don't have to replace every single fader. This was a used board, and everything... Has anyone tried this? Kind regards ---
**Author:** ![pianosso](https://avatars.discourse-cdn.com/v4/letter/p/65b543/32.png) [@pianosso](https://forums.allen-heath.com/u/pianosso)\ **Post date:** [5 May 2024 20:32 UTC](https://forums.allen-heath.com/t/gld80-fader-trembling-help/11871/6 "2024-05-05T20:32:12Z")
I replaced a lot of faders on my GLDs and I think this is the only option without replacing the fader board. So I don’t think is a capacitor issue. ---
**Author:** ![Rainer](https://avatars.discourse-cdn.com/v4/letter/r/58956e/32.png) [@Rainer](https://forums.allen-heath.com/u/Rainer)\ **Post date:** [21 September 2025 16:54 UTC](https://forums.allen-heath.com/t/gld80-fader-trembling-help/11871/7 "2025-09-21T16:54:37Z")
Hey unicomix, Unfortunately not. This problem occurs more often, see here: > [@GLD Fader readout jitter](https://forums.allen-heath.com/t/gld-fader-readout-jitter/23315): > > I’m having a strange issue on my GLD. After I turned it back on after a year or so all fader values are jittering around. Not the physical faders (they move correctly and stop moving once they’ve reached their position) - just the value readout of the fader jumps around. This happens on all fader banks, regardless of the physical fader position. So I suspect something in the fader readout A/D conversion and/or powersupply? Anyone had something like this before? Here is a screencap of GLD-Edit… Kind regards. ---
**Author:** ![davidgiga1993](https://sea2.discourse-cdn.com/flex002/user_avatar/forums.allen-heath.com/davidgiga1993/32/2816_2.png) [@davidgiga1993](https://forums.allen-heath.com/u/davidgiga1993)\ **Post date:** [21 September 2025 18:17 UTC](https://forums.allen-heath.com/t/gld80-fader-trembling-help/11871/8 "2025-09-21T18:17:36Z")
In my case it wasn’t the capacitors. The issue is a high ripple in the 3.3v reference supply for the faders. Adding a much higher capacitance made the issue less prominent, but my guess is that the regulator for the 3.3v was bad. As I didn’t had the part, nor time to replace/try n error this I ended up replacing the entire main fader board (which has the 3.3v reference regulator). ---
**Author:** ![Rainer](https://avatars.discourse-cdn.com/v4/letter/r/58956e/32.png) [@Rainer](https://forums.allen-heath.com/u/Rainer)\ **Post date:** [22 September 2025 07:39 UTC](https://forums.allen-heath.com/t/gld80-fader-trembling-help/11871/9 "2025-09-22T07:39:07Z")
Ok, then I’ll take care of the 3.3 V regulator and try to reduce the voltage ripple. If I find the part and have the time, I’ll give it a try and hope it works. Thanks a lot! Edit: Did you replace both fader banks, the 12-channel bank and the 8-channel bank? ---
**Author:** ![gatoproducciones](https://sea2.discourse-cdn.com/flex002/user_avatar/forums.allen-heath.com/gatoproducciones/32/3056_2.png) [@gatoproducciones](https://forums.allen-heath.com/u/gatoproducciones)\ **Post date:** [13 September 2026 21:20 UTC](https://forums.allen-heath.com/t/gld80-fader-trembling-help/11871/10 "2026-09-13T21:20:44Z")
Hello, esteemed colleague. Could you share where you were able to buy the complete fader bank? Best regards.